BendPak PCL-18B-4 HV / 72,000LB Capacity Mobile Lift Set of 4

This PCL-18B mobile column lift system comes in a set of 4. When combined, the system lifts up to 72,000 lbs. Ideal for two-axle vehicles. Sets of 2, 6 and 8 are also available.
With a full set of mobile column lifts, you’ll lift vehicles up to 72,000 lbs. This weight class encompasses most heavy-duty and commercial semi-trucks. If you need more lifting power, upgrade to a set of 6 or double your capability with a set of 8. For a frame-engaging adapter, check out the PCL-18B cross beam. This handy tool allows you to safely remove tires and perform full wheel service on your vehicle.

Specification: 

–    HIGH VOLTAGE UNITS
–    18,000-lb. individual column capacity / 108,000-lb. maximum system capacity
–    Meets or exceeds the standards prescribed by ANSI/ALI ALCTV-2011
–    Two, four, or six column configurations can accommodate heavy duty trucks and light duty passenger vehicles
–    208-240V, 3-phase main power system – optional voltages available upon request
–    SINGLE, PAIR or TEAM operation
–    For a standard four-column set, just three 30′ cables are used leaving the front or back of the lift clear of cable obstructions
–    Simple operation, long service life and minimum maintenance
–    Intuitive controls allow the lift to be fully programmed and controlled from any column
–    Control systems feature 24-volt safety circuitry
–    The PLC and main system components are standard off-the-shelf brands rather than proprietary printed circuit boards or controls, which can be very expensive to service or replace
–    Smart electronics feature self-diagnostics and self-calibration functions
–    Sealed and enclosed linear potentiometers feature precision potentiometric output and high-frequency response for precise synchronization and communication of all columns throughout all operation cycles for precise, level lifting
–    Variable height limit settings can be programmed for shops with low ceilings or when specific vehicle service requirements necessitate specific rise heights
–    Two-speed lowering option – turtle or rabbit speed settings
–    Each column is equipped with a warning light and audible alarm for critical warning alerts
–    Emergency shut-off switches on each column quickly shut off power to the lift in the event an unsafe condition is detected by the operator
–    Separate key lock enclosure on each column
–    Electronics are multi-fuse protected
–    An enclosed electric-hydraulic power system that ensures quieter operation is better suited for sound-sensitive areas
–    Pallet-jack style steering wheels enable the columns to be lowered firmly on the floor vs. constantly loaded spring-type steering wheels that can cause columns to roll when unladen by the weight of a vehicle
–    Low-mounted power units and cylinders means a lower center of gravity, making the columns easier to move and less likely to topple vs. screw-drive systems with heavy overhead motors and drive systems
–    Extended forks accommodate wide tires and deep wheel configurations
–    Multi-width wheel forks with locking pins accommodate the widest range of wheels, eliminating the need for specialty wheel adapters
–    Tandem 8” diameter polyurethane covered steel wheels with sealed roller bearings easily roll over dirt and debris
–    Heavy-duty steel carriage rollers feature turned, ground and polished axle pins
–    Manual safety override valves on each column permit the lift to be lowered in the event of a power outage without the need for manual hand cranks
–    Durable forklift pockets provide simplistic handling when moving the lift columns from one facility to another
–    Inverted hydraulic cylinders feature an integrated safety valve to prevent accidental uncontrolled lowering in the event of oil pressure loss
–    Multiple, automatic, independent safety locks spaced every four inches ensure safe operation
–    Space-saving design, reduced column weight and a tight turning radius provides improved mobility
–    Use the lift to place vehicles on tall jack stands then use the columns to raise another vehicle in an adjoining bay
–    Durable powder-coat finish

BENDPAK NUMBER #5175296

For warranty information, shipping, and FAQ, please visit: https://www.wurthtool.com/pages/bendpak